Product Lines > CompactPCI Systems > MIC-3376
MIC-3376 6U CompactPCI Pentium® III/II SBC with Ultra2 Wide SCSI/Dual LAN/VGA        Larger image (38 Kb) Introduction Features Specifications Ordering Information Datasheet Download (pdf 185Kb)  Accepts slot 1 processors, including Pentium® III and Pentium® II  Chipset: Intel® 440BX  Single/dual PCI-to-PCI bridge drive up to 7 or 14 CompactPCI slots  Supports Ultra2 Wide SCSI interface
INTRODUCTION
High Performance Pentium® III Processor The MIC-3376 accepts an Intel® slot 1 Pentium III or Pentium II processor. With support for 66/100 MHz CPU bus clock and the CPU's integrated 512 KB L2 cache memory, the MIC-3376 can fulfill customers' most demanding requirements for high-performance computing capability. Compact Mechanical Design The MIC-3376 has rich functions on a single board with only two-slot width. Advantech provides a CPU heat sink specially designed for the SECC 2 Pentium® III/II processor, so the MIC-3376 can operate without a cooling fan on the heat sink. For ventilation, it only requires external cooling air from the chassis fans. This enables the MIC-3376 to use a Pentium® III/II CPU within a mere 2-slot wide space. SCSI, Dual LAN and Dual PCI-to-PCI Bridge An Ultra2 Wide SCSI interface is optionally available on the front panel. It provides connection to an external RAID system and other SCSI devices, with data transfer rate up to 80 MB/s. Dual on-board Fast Ethernet channels provide teaming functions such as Adapter Fault Tolerance, Adaptive Load Balancing and Fast EtherChannel® . These increase transmission throughput and reliability. The MIC-3376 also provides single/dual PCI-to-PCI bridge options, to drive up to 7/14 CompactPCI slots. Complete I/O Functions The MIC-3376 offers all industrial computer I/O functions in a rugged Eurocard form factor. All I/O connectors are available on the front panel, including two Fast Ethernet interfaces, two serial ports, two USB ports, one VGA connector, one SCSI interface, one parallel port, and one PS/2 keyboard/mouse connector. The reset button together with LEDs for power status, HDD operation, SCSI operation, and Ethernet communication are also located on the front panel. The built-in high-speed PCI IDE controller provides two seperate IDE channels with Ultra DMA/33 mode. The user-defined J3 connector supports up to four IDE devices and two FDDs. These drives can be easily connected to the backplane or to the rear transition board, for easy maintenance and service. An optional rear transition board (MIC-3301) can be used to connect a keyboard, a mouse and one serial port from the rear panel. It can also carry a 2.5" hard disk drive and one CompactFlash disk Meets Industrial Applications Requirements The MIC-3376 is designed for use in mission critical applications. It accepts a CompactFlash memory card to eliminate fragile rotating hard drive worries. A watchdog timer can automatically reset the system or generate an interrupt if the system stops due to a program bug or EMI. The two-layer front panel design complies with IEEE 1101.10. Connectors are firmly screwed to the front panel, and the replaceable shielding gasket is attached to the panel edge. This reduces emissions and gives better protection against external interference.
FEATURES
Accepts slot 1 processors, including Pentium® III and Pentium® II Chipset: Intel® 440BX Single/dual PCI-to-PCI bridge drive up to 7 or 14 CompactPCI slots Supports Ultra2 Wide SCSI interface Dual on-board 10/100Base-TX Fast Ethernet with RJ-45 connectors On-board high-performance AGP VGA display Connection to four Ultra DMA/33 high-speed IDE devices (through J3 connector) Accepts CompactFlash memory card Two DIMM sockets support up to 512 MB SDRAM, supports ECC
SPECIFICATIONS
General Specifications CPU: Intel® Pentium® III up to 550 MHz, Pentium® II up to 450 MHz BIOS: Award 2 Mb Flash memory Chipset: Intel® 440BX Front side bus clock: 100/66 MHz Bus interface: 32-bit, 33 MHz, PICMG 2.0 compliant 2nd level cache: CPU built-in 512 KB RAM: Two 168-pin DIMM sockets. Supports up to 512 MB SDRAM, supports ECC Enhanced IDE interface: Handles up to 4 IDE devices. Supports PIO mode 4 and DMA/33 mode. Available through J3 connector Floppy disk drive interface: Supports up to two floppy disk drives. Available through J3 connector CompactFlash interface: Accepts one CompactFlash card on primary IDE channel; master or slave selectable by a jumper Parallel port: Configured to LPT1, LPT2, LPT3 or disabled. Supports multimode parallel (SPP/EPP/ECP) port Ethernet: Two Intel® 82559 Fast Ethernet controller chips, 10/100Base-TX with RJ-45 connectors Serial ports: Two RS-232 ports with 16550 UARTs USB interface: Two USB ports Watchdog timer: Can generate a system reset or IRQ 15. Software enabled/disabled. Time interval is from 1 to 63 seconds. Jumperless with run-time setup Keyboard/mouse connector: One 6-pin mini-DIN connector on the front panel PCI-to-PCI bridge: One or two Intel® DEC 21150 controller chip(s), to drive up to 7 or 14 bus master peripherals AGP VGA Interface Controller: Intel C&T 69000 CPU: AGP 1.0 compliant, 66 MHz Display memory: 2 MB on-chip SDRAM Display resolution: Supports non-interlaced CRT monitor resolutions up to 1280 x 1024 @ 256 colors, or up to 800 x 600 @ 16 million colors Ultra2 Wide SCSI Interface Controller: Symbios SYM53C895 Performs Ultra2 Wide SCSI LVD synchronous transfers as fast as 80 MB/s 68-pin connector on front panel Rear Transition Board (MIC-3301) Rear panel I/O connectors: PS/2 keyboard and mouse, COM 1 On-board brackets to carry a 2.5" hard disk drive Size: 6U high, two-slot width (8 TE) On-board connectors: One floppy disk connector (34-pin 2.54 mm pitch box header), primary IDE connectors (includes one 40-pin 2.54 mm pitch box header, one 44-pin 2.0 mm pitch box header for 2.5" hard disk drive, and one CompactFlash socket), and one secondary IDE connector Mechanical and Environmental Specifications Operating temperature: 0 ~ 50° C (32 ~ 140° F), depending on CPU installed Storage temperature: 20 ~ 70° C (-4 ~ 158° F) Humidity (operating and storage): 5 ~ 95% (non-condensing) Size: 233.35 x 160 mm (6U), 2-slot (8 TE) width Weight: 0.8 kg (1.8 lbs) Shock: 20 G (operating); 50 G (storage/transit)
ORDERING INFORMATION
MIC-3376 : 6U CompactPCI Pentium® III/II processor board with single PCI-to-PCI bridge, dual LAN, VGA, utility CD-ROM disc, manual, and heat sink MIC-3376S : 6U CompactPCI Pentium>® III/II processor board with single PCI-to-PCI bridge, SCSI, dual LAN, VGA, utility CD-ROM, manual, and heat sink MIC-3376D : 6U CompactPCI Pentiumsup>® III/II processor board with dual PCI-to-PCI bridge, dual LAN, VGA, utility CD-ROM disc, manual, and heat sink MIC-3376F : 6U CompactPCI Pentium® III/II processor board with dual PCI-to-PCI bridge, SCSI, dual LAN, VGA, utility CD-ROM disc, manual, and heat sink MIC-3301 : 6U rear transition board. Provides connection to COM1, keyboard and mouse on rear panel. Connectors for two IDE channels on board (for use in a chassis with rear I/O support)
Advantech Home  |  Site Map  |  Service & Support  |  Buy Online Press Room  |  Current Events  |  Products  |  Application Stories  |  Contact Info             Copyright © 2001 Advantech Co., Ltd. Comments, questions, feedback?             All Rights Reserved Email us now